Effect of Solid Loading on the Property of Al2O3 Ceramics in Stereolithographic Additive Manufacturing

doi:10.15541/jim20210636

Abstract

Abstract:

For ceramic stereolithographic (SL) additive manufacturing, the solid loading of ceramic photosensitive slurry plays an important role during the SL process. In this study, Al₂O₃ ceramics were fabricated by SL additive manufacturing from photosensitive Al₂O₃ slurries with various solid loadings, and the solid loading-property relationships of Al₂O₃ ceramic were performed. The effects of solid loading on not only the rheological behavior and curing property of the photosensitive Al₂O₃ slurry but also the microstructure and mechanical properties of the Al₂O₃ ceramic were investigated. The results showed that both the viscosity and shear stress increased with the increase of the solid loading. High viscosity was greater than the critical value for self-leveling during the SL process. The curing properties of photosensitive Al₂O₃ slurries were highly depended on the sold loading. Moreover, clear effects on the defect characteristics of Al₂O₃ ceramics manufactured from various photosensitive slurries were observed. These manufactured defects are critical for the mechanical behavior of Al₂O₃ ceramic. In addition, the relationship between rheological behavior and curing property of photosensitive Al₂O₃ slurry. Meanwhile, the resulting microstructure and mechanical properties of the Al₂O₃ ceramic were also illustrated. Inhomogeneous structure caused by high viscosity can lead to a sintered ceramic with poor strength. These findings provide fundamental understanding for SL additive manufacturing of ceramics.

Key words: Al₂O₃, solid loading, stereolithography, additive manufacturing

CLC Number:

TQ174

LIU Guoqian, YAN Changhai, ZHANG Keqiang, JIN Hua, HE Rujie. Effect of Solid Loading on the Property of Al₂O₃ Ceramics in Stereolithographic Additive Manufacturing[J]. Journal of Inorganic Materials, 2022, 37(3): 353-360.

Figures/Tables 9

References 28

[1]	LAKHDAR Y, TUCK C, BINNER J, et al. Additive manufacturing of advanced ceramic materials. Progress in Materials Science, 2021, 116: 100736. DOI URL
[2]	LI X B, ZHONG H, ZHANG J X, et al. Powder characteristics on the rheological performance of resin-based zirconia suspension for stereolithography. Journal of Inorganic Materials, 2020, 35(2): 231-235.
[3]	HE C, MA C, LI X L, et al. Continuous fast 3D printing of SiOC ceramic components. Additive Manufacturing, 2021, 46: 102111. DOI URL
[4]	YANG L L, ZENG X J, DITTA A, et al. Preliminary 3D printing of large inclined-shaped alumina ceramic parts by direct ink writing. Journal of Advanced Ceramics, 2020, 9: 312-319. DOI URL
[5]	HU X A, ZHAO G L, LIU F C, et al. Microstructure and mechanical behavior of Inconel 625 alloy processed by selective laser melting at high temperature up to 1000 ℃. Rare Metal, 2020, 39: 1181-1189. DOI URL
[6]	CHEN F, ZHU H, WU J M, et al. Preparation and biological evaluation of ZrO₂ all-ceramic teeth by DLP technology. Ceramics International, 2020, 46(8): 11268-11274. DOI URL
[7]	ZHANG K Q, XIE C, WANG G, et al. High solid loading, low viscosity photosensitive Al₂O₃ slurry for stereolithography based additive manufacturing. Ceramics International, 2019, 45(1): 203-208. DOI URL
[8]	CHEN Z W, LI Z Y, LI J J, et al. 3D printing of ceramics: a review. Journal of the European Ceramic Society, 2019, 39(4): 661-687. DOI URL
[9]	HE R J, ZHOU, N P, ZHANG K Q, et al. Progress and challenges towards additive manufacturing of SiC ceramic. Journal of Advanced Ceramics, 2021, 10(4): 637-674. DOI URL
[10]	SU B, DHARA S, WANG L. Green ceramic machining: a top- down approach for the rapid fabrication of complex-shaped ceramics. Journal of the European Ceramic Society, 2008, 28(11): 2109-2115. DOI URL
[11]	LI H, LIU Y S, LIU Y S, et al. Microstructure and mechanical properties of 3D printed ceramics with different vinyl acetate contents. Rare Metals, 2021, 40: 3241-3250. DOI URL
[12]	DING G J, HE R J, ZHANG K Q, et al. Dispersion and stability of SiC ceramic slurry for stereolithography. Ceramics International, 2020, 46(4): 4720-4729. DOI URL
[13]	LI K H, ZHAO Z. The effect of the surfactants on the formulation of UV-curable SLA alumina suspension. Ceramics International, 2017, 43(6): 4761-4767. DOI URL
[14]	NIE J B, LI M S, LIU W W, et al. The role of plasticizer in optimizing the rheological behavior of ceramic pastes intended for stereolithography-based additive manufacturing. Journal of the European Ceramic Society, 2021, 41(1): 646-654. DOI URL
[15]	AZARMI F, ALI A. Microstructural evolution during fabrication of alumina via laser stereolithography technique. Ceramics International, 2019, 45(1): 271-278. DOI URL
[16]	NDINISA S S, WHITEFIELD D J, SIGALAS I. Fabrication of complex shaped alumina parts by gelcasting on 3D printed moulds. Ceramics International, 2020, 46(3): 3177-3182. DOI URL
[17]	WEI J J, LI J L, SONG X X, et al. Effects of solid loading on the rheological behaviors and mechanical properties of injection- molded alumina ceramics. Journal of Alloys and Compounds, 2018, 768: 503-509. DOI URL
[18]	ZHANG K Q, HE R J, DING G J, et al. Digital light processing of 3Y-TZP strengthened ZrO₂ ceramics. Material Science Engineering A, 2020, 774: 138768. DOI URL
[19]	ISO 14704-2000. Fine Ceramics-Test Method for Flexural Strength of Monolithic Ceramics at Room Temperature.
[20]	HERSCHEL W H, BULKLEY R. Konsistenzmessungen von gummi-benzollosungen. Kolloid Zeitschrift, 1926, 39: 291-300. DOI URL
[21]	LEWIS J A. Colloidal processing of ceramics. Journal of the American Ceramic Society, 2000, 83: 2341-2359. DOI URL
[22]	LIU D M. Particle packing and rheological property of highly- concentrated ceramic suspensions: φ_m determination and viscosity prediction. Journal of Materials Science, 2000, 35(21): 5503-5507. DOI URL
[23]	CHARITIER T, CHAPUT C, DOREAU F, et al. Stereolithography of structural complex ceramic parts. Journal of Materials Science, 2002, 37: 3141-3147. DOI URL
[24]	ABOULIATIM Y, CHARTIER T, ABELARD P, et al. Optical characterization of stereolithography alumina suspensions using the Kubelka-Munk model. Journal of the European Ceramic Society, 2009, 29(5): 919-924. DOI URL
[25]	GRIFFITH M L, HALLORAN J W. Freeform fabrication of ceramics via stereolithography. Journal of the American Ceramic Society, 1996, 79: 2601-2608. DOI URL
[26]	DIENER S, FRANCHIN G, ACHILLES N, et al. X-ray microtomography investigations on the residual pore structure in silicon nitride bars manufactured by Direct Ink Writing using different printing patterns. Open Ceramic, 2021, 5: 100042.
[27]	ZHANG K Q, MENG Q Y, CAI N J, et al. Effects of solid loading on stereolithographic additive manufactured ZrO₂ ceramic: a quantitative defect study by X-ray computed tomography. Ceramics International, 2021, 47(17): 24353-24359. DOI URL
[28]	ZHANG K Q, HE R J, DING G J, et al. Effects of fine grains and sintering additives on stereolithography additive manufactured Al₂O₃ ceramic. Ceramics International, 2021, 47(1): 2303-2310. DOI URL

Solid loading /% (in volume)	τ₀/Pa	K	n	R²
45	1.24243	0.41855	0.99596	0.99825
50	1.43614	0.37397	1.09476	0.99871
55	1.77148	0.37481	1.14081	0.99883
60	2.26134	0.57750	1.25022	0.99975
65	3.97074	1.87845	1.22798	0.99992

Solid loading /% (in volume)	τ₀/Pa	K	n	R²
45	1.24243	0.41855	0.99596	0.99825
50	1.43614	0.37397	1.09476	0.99871
55	1.77148	0.37481	1.14081	0.99883
60	2.26134	0.57750	1.25022	0.99975
65	3.97074	1.87845	1.22798	0.99992

Effect of Solid Loading on the Property of Al₂O₃ Ceramics in Stereolithographic Additive Manufacturing

RichHTML

PDF (PC)

Knowledge

Abstract

Cite this article

share this article

Figures/Tables 9

References 28

Related Articles 15

Recommended Articles

Metrics

Comments

[1]	YUAN Jingkun, XIONG Shufeng, CHEN Zhangwei. Research Trends and Challenges of Additive Manufacturing of Polymer-derived Ceramics [J]. Journal of Inorganic Materials, 2023, 38(5): 477-488.
[2]	ZHU Qingong, ZHAO Gaoling, HAN Gaorong. Effect of Recombination Time on the Structure and Properties of P₂O₅-Al₂O₃ Heterogeneous Composite Glass [J]. Journal of Inorganic Materials, 2023, 38(2): 170-176.
[3]	NAN Bo, ZANG Jiadong, LU Wenlong, YANG Tingwang, ZHANG Shengwei, ZHANG Haibo. Recent Progress on Additive Manufacturing of Piezoelectric Ceramics [J]. Journal of Inorganic Materials, 2022, 37(6): 585-595.
[4]	LI Haiyan, HAO Hongjian, TIAN Yuan, WANG Changan, BAO Yiwang, WAN Detian. Effects of Residual Stresses on Strength and Crack Resistance in ZrO₂ Ceramics with Alumina Coating [J]. Journal of Inorganic Materials, 2022, 37(4): 467-472.
[5]	CAO Jiwei, WANG Pei, LIU Zhiyuan, LIU Changyong, WU Jiamin, CHEN Zhangwei. Research Progress on Powder-based Laser Additive Manufacturing Technology of Ceramics [J]. Journal of Inorganic Materials, 2022, 37(3): 241-254.
[6]	LIU Haifang, SU Haijun, SHEN Zhonglin, JIANG Hao, ZHAO Di, LIU Yuan, ZHANG Jun, LIU Lin, FU Hengzhi. Research Progress on Ultrahigh Temperature Oxide Eutectic Ceramics by Laser Additive Manufacturing [J]. Journal of Inorganic Materials, 2022, 37(3): 255-266.
[7]	YANG Yong, GUO Xiaotian, TANG Jie, CHANG Haotian, HUANG Zhengren, HU Xiulan. Research Progress and Prospects of Non-oxide Ceramic in Stereolithography Additive Manufacturing [J]. Journal of Inorganic Materials, 2022, 37(3): 267-277.
[8]	LIU Kai, SUN Ce, SHI Yusheng, HU Jiaming, ZHANG Qingqing, SUN Yunfei, ZHANG Song, TU Rong, YAN Chunze, CHEN Zhangwei, HUANG Shangyu, SUN Huajun. Current Status and Prospect of Additive Manufacturing Piezoceramics [J]. Journal of Inorganic Materials, 2022, 37(3): 278-288.
[9]	ZHOU Ganghuai, LIU Yao, SHI Yuan, LIU Shaojun. Slurry Preparation and Stereolithography for Activated Alumina Catalyst Carrier [J]. Journal of Inorganic Materials, 2022, 37(3): 297-302.
[10]	WANG Yaning, ZHANG Yuqi, SONG Suocheng, CHEN Ruomeng, LIU Yaxiong, DUAN Yugang. Laser Stereolithography for Zirconia Ceramic Fabrication and Its Debinding and Sintering Process [J]. Journal of Inorganic Materials, 2022, 37(3): 303-309.
[11]	LI Meng, HUANG Hailu, WU Jiamin, LIU Chunlei, WU Yaru, ZHANG Jingxian, SHI Yusheng. Effect of Solid Loading of Slurry on Properties of Si₃N₄ Ceramics Formed by Digital Light Processing [J]. Journal of Inorganic Materials, 2022, 37(3): 310-316.
[12]	LI Qiaolei, GU Yue, YU Xuehua, ZHANG Chaowei, ZOU Mingke, LIANG Jingjing, LI Jinguo. Effect of Sintering Temperature on Surface Morphology and Roughness of 3D-printed Silicon Ceramic Cores [J]. Journal of Inorganic Materials, 2022, 37(3): 325-332.
[13]	CHENG Ziqiu, WANG Yanbin, LIU Xin, DAI Zhengfa, CHEN Haohong, TIAN Feng, CHEN Penghui, LI Jiang. Component Regulation and Performance Optimization of Al₂O₃-YAG:Ce Composite Ceramic Phosphors for High-power Laser Lighting [J]. Journal of Inorganic Materials, 2022, 37(12): 1358-1364.
[14]	ZHU Quan, HU Jianbao, YANG Jinshan, ZHOU Haijun, DONG Shaoming. Strong SiC Porous Ceramic Obtained by Sintering of Reticulated Aligned SiC Nanowires [J]. Journal of Inorganic Materials, 2021, 36(5): 547-551.
[15]	SHEN Lu, WANG Dewen, HUANG Rong, DU Shiyu, HUANG Qing. Electron Irradiation Induced Phase-separation Behavior in AlF₃ Doped Alumina Ceramic with Superior Sensitivity [J]. Journal of Inorganic Materials, 2021, 36(1): 95-100.