Zn-Sb双掺杂Mg2(Si,Sn)合金的热电性能

doi:10.15541/jim20180388

摘要/Abstract

摘要：

Mg₂(Si,Sn)合金热电材料具有成本低廉、环境友好等优点, 作为一种绿色环保的中温区热电材料一直受到广泛关注。在Mg₂(Si,Sn)基材料中掺杂大剂量Sb可诱发Mg空位, 从而有效降低材料的热导率, 但同时Seebeck系数也会降低。研究采用高温熔炼及真空热压法成功合成了Mg_2.12-_ySi_0.4Sn_0.5Sb_0.1Zn_y (y=0~0.025)试样, 通过在大剂量Sb掺杂的Mg₂(Si,Sn)基材料中添加Zn元素, 研究了大剂量Sb和微量Zn双掺杂对材料电声输运特性的综合影响。研究结果表明, Zn-Sb双掺杂可通过有效抑制材料电子热导率的方法大幅降低Mg₂(Si,Sn)合金材料的总热导率, 与此同时明显提高掺Zn试样的塞贝克系数以弥补其电导率的损失, 维持材料较为优异的电学性能。最终, 热导率的大幅优化及电学性能的维持实现了材料综合热电性能的显著提升, 其中, 成分为Mg_2.095Si_0.4Sn_0.5Sb_0.1Zn_0.025的材料在823 K下热电优值ZT达到1.42。

关键词: 热电材料, Mg₂(Si, Sn)合金, Zn-Sb双掺杂, 热电优值

Abstract:

As a type of medium-temperature thermoelectric materials, Mg₂(Si,Sn) alloy thermoelectric materials have been widely concerned because of the low cost and environmental friendliness. Heavily Sb doping can effectively induce Mg vacancy so as to reduce the thermal conductivity in Mg₂(Si,Sn)-based materials, but at the same time lead to a decrease of Seebeck coefficient. In this study, high-quality Mg_2.12-_ySi_0.4Sn_0.5Sb_0.1Zn_y (y=0-0.025) samples were successfully synthesized by high temperature melting and vacuum hot-pressing method. Zn element was introduced into the heavily Sb-doped Mg₂(Si,Sn) material to investigate the double doping effect on the electroacoustic transport properties. The results show that Zn-Sb double doping could effectively reduce the total thermal conductivity of Mg₂(Si,Sn)-based materials by obviously suppressing the electronic thermal conductivity and at the same time enhance the Seebeck coefficient of Zn-doped samples, so as to compensate for the loss of electrical conductivity, and maintain high electrical performance. Significantly optimized thermal conductivity and electrical performance ultimately improve the thermoelectric figure of meritZT of the material. At 823 K, the maximum ZT of Mg_2.095Si_0.4Sn_0.5Sb_0.1Zn_0.025 reached 1.42.

Key words: thermoelectric materials, Mg₂(Si, Sn) alloy, zinc-antimony doping, figure of merit

中图分类号:

TB381

余冠廷, 忻佳展, 朱铁军, 赵新兵. Zn-Sb双掺杂Mg₂(Si,Sn)合金的热电性能[J]. 无机材料学报, 2019, 34(3): 310-314.

YU Guan-Ting, XIN Jia-Zhan, ZHU Tie-Jun, ZHAO Xin-Bing. Thermoelectric Property of Zn-Sb Doped Mg₂(Si,Sn) Alloys[J]. Journal of Inorganic Materials, 2019, 34(3): 310-314.

图/表 5

图1 Mg2.12-ySi0.4Sn0.5Sb0.1Zny (y=0~0.025)的XRD图谱

Fig.1 XRD patterns of Mg2.12-ySi0.4Sn0.5Sb0.1Zny (y=0-0.025)

图2 Mg2.12-ySi0.4Sn0.5Sb0.1Zny试样的背散射SEM照片

Fig.2 Backscattered SEM images of Mg2.12-ySi0.4Sn0.5Sb0.1Zny(a) y=0.015; (b)y=0.025

图3 Mg2.12-ySi0.4Sn0.5Sb0.1Zny (y=0~0.025)的电学性能随温度的变化关系

Fig.3 Temperature dependences of electrical properties of Mg2.12-ySi0.4Sn0.5Sb0.1Zny (y=0-0.025)(a) Electrical conductivity; (b) Seebeck coefficient; (c) Power factor

图4 Mg2.12-ySi0.4Sn0.5Sb0.1Zny(y=0~0.025)的热导率随温度变化的关系曲线

Fig.4 Temperature dependences of thermal properties of Mg2.12-ySi0.4Sn0.5Sb0.1Zny(y=0-0.025)(a) Total thermal conductivity; (b) Lattice thermal conductivity

图5 Mg2.12-ySi0.4Sn0.5Sb0.1Zny(y=0~0.025)热电优值ZT随温度的变化曲线

Fig.5 Temperature dependences of figure of merit ZT for Mg2.12-ySi0.4Sn0.5Sb0.1Zny(y=0-0.025)

参考文献 26

[1]	HE J, TRITT T M. Advances in thermoelectric materials research: looking back and moving forward. Science, 2017, 357(6358): 1369-1-9.
[2]	ZHU T J, LIU Y T, FU C G, et al. Compromise. Compromise and synergy in high-efficiency thermoelectric materials. Advanced Materials, 2017, 29(14): 1605884-1-26.
[3]	HU L P, ZHU T J, LIU X H,et al. Point defect engineering of high-performance bismuth-telluride-based thermoelectric materials. Advanced Functional Materials, 2014, 24: 5211-5218.
[4]	ZHAI R S, WU Y H, ZHU T J,et al. Thermoelectric performance of p-type zone-melted Se-doped Bi0.5Sb1.5Te3 alloys. Rare Metals, 2018, 37(4): 308-315.
[5]	ZHANG Q H, XU L L, WANG L J,et al. Effects of different amount of Se-doping on microstructures and thermoelectric properties of n-type Bi2Te3-xSex. Journal of Inorganic Materials, 2014, 29(11): 1139-1144.
[6]	YING P J, LIU X H, FU C G,et al. High performance α-MgAgSb thermoelectric materials for low temperature power generation. Chemistry of Materials, 2015, 27(3): 909-913.
[7]	PEI Y Z, LALONDE A D, WANG H,et al. Low effective mass leading to high thermoelectric performance. Energy & Environmental Science, 2012, 5(7): 7963-7969.
[8]	QIN B C, XIAO Y, ZHOU Y M,et al. Thermoelectric transport properties of Pb-Sn-Te-Se system. Rare Metals, 2017, 37(4): 343-350.
[9]	LIU X H, ZHU T J, WANG H,et al. Low electron scattering potentials in high performance Mg2Si0.45Sn0.55 based thermoelectric solid solutions with band convergence. Advanced Energy Materials, 2013, 3(9): 1238-1244.
[10]	JIANG G Y, HE J, ZHU T J,et al. High performance Mg2(Si,Sn) solid solutions: a point defect chemistry approach to enhancing thermoelectric properties.Advanced Functional Materials, 2014, 24(24): 3776-3781.
[11]	CHEN X, GIRARD S N, MENG F, et al. Approaching the minimum thermal conductivity in rhenium-substituted higher manganese silicides. Advanced Energy Materials, 2014, 4(14): 1400452-1-10.
[12]	ZAITSEV V K, FEDOROV M I, GURIEVA E A, et al. Highly effective Mg2Si1-xSnx thermoelectrics. Physical Review B, 2006, 74(4): 045207-1-5.
[13]	YAO Z, QIU P F, LI X Y,et al. Investigation on quick fabrication of n-type filled skutterudites. Journal of Inorganic Materials, 2016, 31(12): 1375-1382.
[14]	SLACK G A, HUSSAIN M A.The maximum possible conversion efficiency of silicon-germanium thermoelectric generators.Journal of Applied Physics, 1991, 70(5): 2694-2718.
[15]	VINING C B, LASKOW W, HANSON J O,et al. Thermoelectric properties of pressure-sintered Si0.8Ge0.2 thermoelectric alloys. Journal of Applied Physics, 1991, 69(8): 4333-4340.
[16]	ZHU T J, FU C G, XIE H H, et al. High efficiency half-Heusler thermoelectric materials for energy harvesting. Advanced Energy Materials, 2015, 5(19): 1500588-1-13.
[17]	FU C G, BAI S Q, LIU Y T, et al. Realizing high figure of merit in heavy-band p-type half-Heusler thermoelectric materials. Nature Communications, 2015, 6: 8144-1-7.
[18]	BROWN S R, KAUZLARICH S M, GASCOIN F,et al. Yb14MnSb11 new high efficiency thermoelectric material for power generation. Chemistry of Materials, 2006, 18: 1873-1877.
[19]	GAO H L, ZHU T J, LIU X X,et al. Flux synthesis and thermoelectric properties of eco-friendly Sb doped Mg2Si0.5Sn0.5 solid solutions for energy harvesting. Journal of Materials Chemistry, 2011, 21(16): 5933-5937.
[20]	HAN Z M, ZHANG X, LU Q M,et al. Preparation and thermoelectric properties of (Mg2Si1-xSbx)0.4-(Mg2Sn)0.6 alloys. Journal of Inorganic Materials, 2012, 27(8): 822-826.
[21]	DU Z L, ZHU T J, CHEN Y,et al. Roles of interstitial Mg in improving thermoelectric properties of Sb-doped Mg2Si0.4Sn0.6 solid solutions. Journal of Materials Chemistry, 2012, 22(14): 6838-6844.
[22]	LIU W, TANG X F, LI H,et al. Optimized thermoelectric properties of Sb-doped Mg2(1+z)Si0.5-ySn0.5Sby through adjustment of the Mg content.Chemistry of Materials, 2011, 23(23): 5256-5263.
[23]	GAO H L, ZHU T J, ZHAO X B,et al. Influence of Ca substitution on the thermoelectric properties of Mg2Si. Journal of Materials Science & Engineering, 2010, 28(2): 260-262.
[24]	GAO H L, ZHU T J, ZHAO X B,et al. Synergetic effect of Zn substitution on the electron and phonon transport in Mg2Si0.5Sn0.5-based thermoelectric materials. Dalton Transactions, 2014, 43(37): 14072-14078.
[25]	YANG S H, ZHU T J, SUN T, et al. Nanostructures in high-performance (GeTe)x(AgSbTe2)100-x thermoelectric materials. Nanotechnology, 2008, 19(24): 245707-1-5.
[26]	ZHAO J B, LIU Z X, REID J,et al. Thermoelectric and electrical transport properties of Mg2Si multi-doped with Sb, Al and Zn. Journal of Materials Chemistry A, 2015, 3(39): 19774-19782.

Zn-Sb双掺杂Mg₂(Si,Sn)合金的热电性能

Thermoelectric Property of Zn-Sb Doped Mg₂(Si,Sn) Alloys

RichHTML

PDF (PC)

可视化

被引次数

摘要/Abstract

引用本文

使用本文

图/表 5

参考文献 26

相关文章 15

编辑推荐

Metrics

本文评价

[1]	贺丹琪, 魏明旭, 刘蕤之, 汤志鑫, 翟鹏程, 赵文俞. 一步法制备重费米子YbAl₃热电材料及其性能提升[J]. 无机材料学报, 2023, 38(5): 577-582.
[2]	王鹏将, 康慧君, 杨雄, 刘颖, 程成, 王同敏. 熵调控抑制ZrNiSn基half-Heusler热电材料的晶格热导率[J]. 无机材料学报, 2022, 37(7): 717-723.
[3]	程成, 李建波, 田震, 王鹏将, 康慧君, 王同敏. In₂O₃/InNbO₄复合材料的热电性能研究[J]. 无机材料学报, 2022, 37(7): 724-730.
[4]	娄许诺, 邓后权, 李爽, 张青堂, 熊文杰, 唐国栋. Ge掺杂MnTe材料的热电输运性能[J]. 无机材料学报, 2022, 37(2): 209-214.
[5]	金敏, 白旭东, 张如林, 周丽娜, 李荣斌. 区熔法制备金属硫化物Ag₂S及其热电性能研究[J]. 无机材料学报, 2022, 37(1): 101-106.
[6]	张岑岑, 王雪, 彭良明. 基于分步式双重调控n型(PbTe)_1-_x_-_y(PbS)_x(Sb₂Se₃)_y体系的热电传输特性[J]. 无机材料学报, 2021, 36(9): 936-942.
[7]	杨青雨, 仇鹏飞, 史迅, 陈立东. 熵工程在热电材料中的应用[J]. 无机材料学报, 2021, 36(4): 347-354.
[8]	蔡剑锋, 王泓翔, 刘国强, 蒋俊. 热电材料中的高熵结构设计[J]. 无机材料学报, 2021, 36(4): 399-404.
[9]	康慧君,张校影,王燕遐,李建波,杨雄,刘达权,杨泽荣,王同敏. 变价稀土元素Eu掺杂BiCuSeO热电性能的研究[J]. 无机材料学报, 2020, 35(9): 1041-1046.
[10]	邱小小,周细应,傅赟天,孙晓萌,王连军,江莞. Ge_1-_xIn_xTe微观结构对热电性能的影响[J]. 无机材料学报, 2020, 35(8): 916-922.
[11]	周星圆, 柳伟, 张程, 华富强, 张敏, 苏贤礼, 唐新峰. Nb掺杂Mo_1-_xW_xSeTe固溶体的热-电输运性能优化[J]. 无机材料学报, 2020, 35(12): 1373-1379.
[12]	李鑫, 席丽丽, 杨炯. 热电材料的第一性原理高通量研究[J]. 无机材料学报, 2019, 34(3): 236-246.
[13]	骆军, 何世洋, 李志立, 李永博, 王风, 张继业. 热电材料高通量实验制备与表征方法[J]. 无机材料学报, 2019, 34(3): 247-259.
[14]	沈家骏, 方腾, 傅铁铮, 忻佳展, 赵新兵, 朱铁军. 热电材料中的晶格热导率[J]. 无机材料学报, 2019, 34(3): 260-268.
[15]	刘虹霞, 李文, 张馨月, 李娟, 裴艳中. (Ag₂Se)_1-_x(Bi₂Se₃)_x的热电性能研究[J]. 无机材料学报, 2019, 34(3): 341-348.