Ag-Cu钎料与双相陶瓷透氧膜的润湿和界面反应研究

doi:10.15541/jim20150551

无机材料学报 ›› 2016, Vol. 31 ›› Issue (6): 607-612.DOI: 10.15541/jim20150551

Ag-Cu钎料与双相陶瓷透氧膜的润湿和界面反应研究

张莉莉, 李可, 于称称, 张玉文, 吴成章, 丁伟中

(上海大学省部共建高品质特殊钢冶金与制备国家重点实验室, 上海 200072)

收稿日期:2015-11-09 修回日期:2015-12-23 出版日期:2016-06-20 网络出版日期:2016-05-19
作者简介:张莉莉(1991–), 女, 硕士研究生. E-mail: springzlli@163.com
基金资助:
国家自然科学基金(51174133, 51274139);国家杰出青年科学基金(51225401)

Wetting Properties and Interface Reaction Mechanism of Ag-Cu Brazes on Dual-phase Membrane Ceramic

ZHANG Li-Li, LI Ke,YU Chen-Chen, ZHANG Yu-Wen, WU Cheng-Zhang, DING Wei-Zhong

(State Key Laboratory of Advanced Special Steels, Shanghai University, Shanghai 200072, China)

Received:2015-11-09 Revised:2015-12-23 Published:2016-06-20 Online:2016-05-19
About author:ZHANG Li-Li. E-mail: springzlli@163.com
Supported by:
National Natural Science Foundation of China (51174133, 51274139);National Science Fund for Distinguished Young Scholars (51225401)

摘要/Abstract

摘要：

用座滴法测试Ag-Cu合金钎料对Ce_0.8Gd_0.2O_2-_δ-NdBaCo₂O₅₊_δ(CGO-NBCO)双相透氧膜的润湿性, 利用SEM-EDS分析润湿和界面反应机理。结果表明: 空气条件下Ag-Cu合金与CGO-NBCO间的润湿遵从界面反应润湿机制。随着Cu含量的增加, Ag-Cu合金对透氧膜润湿性能提高, Cu含量为6.6mol%~15.8mol%时, 润湿角在35°~20°左右。在润湿界面处出现Cu氧化物的富集, 并且在透氧膜侧生成一层由Cu氧化物和CGO-NBCO双相透氧膜反应产生的Ba-Cu-O、Co-Cu-O和Nd-Ce-Cu-O等复杂氧化物相构成的产物层, 新的界面反应层的生成有利于Ag基合金钎料的润湿, 改善了钎料的润湿性能。

关键词: Ag-Cu合金, CGO-NBCO双相透氧膜, 润湿, 界面反应

Abstract:

A reactive air brazing Ag-CuO alloy was evaluated for brazing dual phase oxygen membrane Ce_0.8Gd_0.2O_2-_δ- NdBaCo₂O₅₊_δ (CGO-NBCO). Contact angle tests were observed between Ag-Cu brazes and CGO-NBCO in air and the interfacial microstructures of the used samples were evaluated by SEM. The results indicate that the wetting angle decreases from 35° to 20° with the content of Cu increased from 6.6mol% to 15.8mol%. It is found that there are copper oxide-enriched zones formed in the junction of the alloy and substrate. The wettability between Ag-CuO alloy and oxygen membrane CGO-NBCO is improved due to the interfacial reaction between Cu oxides in braze and the surface layers of CGO-NBCO substrates to form compounds of Ba-Cu-O, Co-Cu-O and Nd-Ce-Cu-O oxides. The new formed interface reaction layers promote the wettability of the rest braze.

Key words: Ag-Cu alloy brazing filler, dual-phase membranes ceramic, wettability, interface reaction

中图分类号:

TQ174

张莉莉, 李可, 于称称, 张玉文, 吴成章, 丁伟中. Ag-Cu钎料与双相陶瓷透氧膜的润湿和界面反应研究[J]. 无机材料学报, 2016, 31(6): 607-612.

ZHANG Li-Li, LI Ke,YU Chen-Chen, ZHANG Yu-Wen, WU Cheng-Zhang, DING Wei-Zhong. Wetting Properties and Interface Reaction Mechanism of Ag-Cu Brazes on Dual-phase Membrane Ceramic[J]. Journal of Inorganic Materials, 2016, 31(6): 607-612.

图/表 6

表1 Ag-Cu钎料成分/mol%

Table 1 Composition of Ag-Cu brazes/mol%

Braze	Cu	Ag
Ag	0	100
Ag -6.6Cu	6.6	93.4
Ag -11.0Cu	11.0	89.0
Ag -15.8Cu	15.8	84.2

图1 CGO-NBCO的XRD图谱

Fig. 1 XRD pattern of CGO-NBCO

图2 不同温度下Ag-Cu合金与CGO-NBCO的润湿角

Fig. 2 Contact angles between Ag-Cu and CGO-NBCO as a function of temperature

图3 Ag-Cu钎料与CGO-NBCO双相透氧膜间润湿界面形貌

Fig. 3 Morphologies of the interfaces between Ag-Cu brazes and CGO-NBCO membrane after wetting experiments. (a) Ag; (b) Ag-6.6Cu; (c) Ag-11Cu; (d) Ag-15.8Cu

图4 不同Ag-Cu钎料与CGO-NBCO双相膜润湿界面处面扫描能谱分析

Fig. 4 EDS analyses of the interface between Ag-Cu brazes and CGO-NBCO membrane

图5 Ag-CuO相图[14]

Fig. 5 Pseudobinary Ag-CuO phase diagram[14]

参考文献 14

[1]	WEIL K S, HARDY J S, RICE J P, et al.Brazing as a means of sealing ceramic membranes for use in advanced coal gasiﬁcation processes.Fuel, 2006, 85(2): 156-162.
[2]	SHAO ZONG-PING, XIONG GUO-XING.Mixed conducting oxygen permeative membranes and their application in partial oxidation of methane to syngas process.Process in Chemical, 1999, 11(1): 30-40.
[3]	TONG JIAN-HUA, YANG WEI-SHEN.Methods for selection perovskite-type oxides used as mixed-conducting membranes for oxygen separation.Membrane Science and Technology, 2003, 23(1): 33-42.
[4]	CHUANGANG FAN, WEI LIU, ZENGQIANG DENG, et al.Mechanical stability and transport properties of the Sn-promoted SrCo0.8Fe0.2O3-δ ceramic membrane.Journal of Membrane Science, 2007, 290(1/2): 73-77.
[5]	HARDY J S, KIM J Y, WEIL K S.Joining mixed conducting oxides using an air-fired electrically conductive braze.Journal of the Electrochemical Society, 2004, 151(8): 43-49.
[6]	WEIL K S, KIMJ Y, HARDY J S.Interfacial analysis of (La0.6Sr0.4)(Co0.2Fe0.8)O3-δ substrates wetted by Ag-CuO.Journal of Material Science, 2005(40): 2341-2348.
[7]	DABBARH S, PFAFF A, ZIOMBRA A, et al.Brazing of mice ceramics to high temperature metals.Ceramic Transactions, 2010 (215): 213-223.
[8]	WANG FANG, ZHANG YU-WEN, DING WEI-ZHONG, et al.Pure Cu braze for sealing oxygen-permeable membrane ceramics and stainless steel support.Journal of Functional Materials, 2010, 41(9): 1540-1542.
[9]	WANG FANG, LIU YONG, LU XION-GANG, et al.Effect of Cu content on interface microstructures of oxygen-permeable membrane brazed with Ag-Cu brazing filler.Rare Meterials and Engineering, 2011, 40(10): 1832-1835.
[10]	LIU JIAO, ZHANG YU-WEN, LIU XU, et al.The effect of temperature on the interface reaction and connectivity between Ag-Cu alloy braze and ceramic oxygen-permeable membrane.Journal of Functional Materials, 2011, 42(2): 313-317.
[11]	ZHANG QI-FEI, GENG ZHEN, ZHANG YU-WEN, et al.The wetting and interface reaction mechanism of Ag-Cu-O brazes on BaCo0.7Fe0.2Nb0.1O3-δ oxygen-permeable membrane ceramic.Journal of Functional Materials, 2012, 43(1): 77-80.
[12]	刘蛟. Ag-Cu钎料与透氧膜陶瓷的润湿及界面反应研究. 上海: 上海大学硕士学位论文, 2013.
[13]	NEVRIVA M, KRAUS H, SEDMIDUBSKY D.Phase equilibria study in the partially open Cu-(O) and Me-Cu-, 1995(282/283): 205-224.
[14]	SHAO Z B, LIU K R, LIU Q L, et al.Eauilibrium phase diagrams in the systems PbO-Ag and CuO-Ag.Journal of the American Ceramic Society, 1993, 76(10): 2663-2664.

[1]	丁健翔,黄培艳,查余辉,汪丹丹,张培根,田无边,孙正明. 高纯Ti₂AlC粉末的无压制备及其在Ag基电触头材料的应用[J]. 无机材料学报, 2020, 35(6): 729-734.
[2]	赵占奎, 李涛, 鲁书含, 王明罡, 张京京, 程道文, 吴臣, 迟悦, 王虹力. SPS界面反应增强机制调控的软磁复合材料磁性能和电阻率[J]. 无机材料学报, 2020, 35(11): 1223-1226.
[3]	李栋, 雷超, 赖华, 刘小林, 姚文俐, 梁彤祥, 钟盛文. 全固态锂离子电池正极与石榴石型固体电解质界面的研究进展[J]. 无机材料学报, 2019, 34(7): 694-702.
[4]	张浩, 高鹏越, 陈光耀, 李明阳, 鲁雄刚, 李重河. Al₂O₃/BaZrO₃双陶瓷界面微观组织演化及机理[J]. 无机材料学报, 2017, 32(8): 819-824.
[5]	陈凡, 石恺成, 孙士阳, 赵博文, 尚海龙, 李戈扬. 不基于熔态润湿的Al/Al₂O₃直接钎焊[J]. 无机材料学报, 2016, 31(6): 602-606.
[6]	刘旭光，马欣，刘勇，张宝泉. 无定形晶种引导三次生长制备完备性TAPO-5膜[J]. 无机材料学报, 2015, 30(5): 555-560.
[7]	鲁元, 李京龙, 杨建锋, 李鹏. 热处理温度对双连续β-氮化硅增强铝基复合材料性能的影响[J]. 无机材料学报, 2015, 30(3): 277-281.
[8]	罗凌虹, 余辉, 黄祖志. 中温固体氧化物燃料电池封接玻璃的研究进展[J]. 无机材料学报, 2015, 30(2): 113-121.
[9]	王贺云, 刘茜, 周遥, 周真真，刘光辉. 碳纤维复合Si₃N₄陶瓷材料的制备及性能研究[J]. 无机材料学报, 2014, 29(9): 1003-1008.
[10]	陆有军, 王燕民, 潘志东, 黄振坤, 吴澜尔. 纳米碳含量对碳/碳化硅陶瓷的机械加工性及与玻璃熔体润湿性的影响[J]. 无机材料学报, 2014, 29(4): 429-432.
[11]	路金蓉, 周洋, 李海燕, 郑涌, 李世波, 黄振莺. Cu/Ti₃SiC₂体系润湿性及润湿过程的研究[J]. 无机材料学报, 2014, 29(12): 1313-1319.
[12]	张强, 姜龙涛, 武高辉. 无压浸渗法制备氧化态SiC颗粒增强铝基复合材料[J]. 无机材料学报, 2012, 27(4): 353-357.
[13]	黄麟, 宁聪琴, 丁冬雁, 白硕, 秦锐, 李明, 毛大立. 掺杂TiO₂纳米管的润湿性能与体外生物活性[J]. 无机材料学报, 2010, 25(7): 775-779.
[14]	李家科,刘磊,刘意春,张文龙,胡文彬. Ti-Si共晶钎料的制备及其对SiC陶瓷可焊性[J]. 无机材料学报, 2009, 24(1): 204-208.
[15]	杨靖,陈杰瑢,余嵘. 溶胶-凝胶法改性SiO₂膜的润湿性与水汽稳定性[J]. 无机材料学报, 2008, 23(4): 739-744.

Ag-Cu钎料与双相陶瓷透氧膜的润湿和界面反应研究

Wetting Properties and Interface Reaction Mechanism of Ag-Cu Brazes on Dual-phase Membrane Ceramic

RichHTML

PDF (PC)

可视化

被引次数

摘要/Abstract

引用本文

使用本文

图/表 6

参考文献 14

相关文章 15

编辑推荐

Metrics

本文评价